specifcations cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 type thas,thinpack, aluminum electrolytic capacitor, 105 oc highlights - 9 mm thin - very high energy density (up to .9 j/cc) - 3000 hr life @ 105 oc - reach and rohs compliant temperature range C55 c to +105 c 300 vdc; -40 oc to 105 oc 350 vdc rated voltage range 10 vdc to 450 vdc capacitance range 60 f to 18000 f capacitance tolerance 20% leakage current 0.002 cv a, @ 25 c and 5 mins. at rated voltage ripple current multipliers low temperature characteristics impedance ratio: z C55 ?c M z +25 ?c @120 hz 10 (5 - 20 vdc), 3 (25 - 300 vdc) z -40 oc /z +25 oc @120 hz 10 (350 vdc) dc life test 3000 h @ rated voltage at 105 c ? capacitance 20% (<50 vdc) ? capacitance 10% (50 vdc) esr 200% of limit dcl 100% of limit shelf life test 5 yrs @ 40 oc capacitance 100% of limit esr 100% of limit dcl 0.004 cv a frequency multipliers rated vdc/freq 50 60 120 360 1000 5000 20000 10-35 0.72 0.77 1.00 1.06 1.06 1.10 1.10 36-60 0.70 0.75 1.00 1.06 1.10 1.20 1.20 61-100 0.70 0.75 1.00 1.06 1.10 1.30 1.30 101-450 0.70 0.75 1.00 1.20 1.45 1.70 1.70 at 9 mm thin, type thas thinpack ofers the highest energy density available in a low profle aluminum electrolytic. its ideal for the lowest profle circuits where high capacitance is needed for bulk storage. look to type thas to replace arrays of smt solid tantalum or aluminum electrolytic capacitors. high energy density, reach and rohs compliant ambient air temperature multipliers (no heat sink) air velocity m/sec 0.25 1.00 2.50 5.00 ripple current multiplier 1.00 1.20 1.50 1.70 temperature multipliers temp 45 55 65 75 85 95 105 0-300 vdc 1.40 1.30 1.20 1.10 1.00 0.60 0.20 301-450 vdc 1.30 1.25 1.15 1.10 1.00 0.60 0.20
vibration mounting: vibration capability is dependent upon mounting restraint. mil-std-202, meth. 204, sine swept, iec 60068-2-6 all sizes = 10g mil-std-202, meth. 204, condition h vibration test level the specimens, while deenergized or operating under the load conditions specied, shall be subected to the vibration amplitude, frequency range, and duration specied for each case size. amplitude the specimens shall be subected to a simple harmonic motion having an amplitude of either 0.06-inch double amplitude (maximum total excursion) or peak level specied above, whichever is less. the tolerance on vibration amplitude shall be 10 percent. frequency range the vibration frequency shall be varied logarithmically between the approximate limits of 10 to 2,000 hz. sweep time and duration the entire frequency range of 10 to 2,000 hz and return to 10 hz shall be traversed in 20 minutes. this cycle shall be performed 12 times in each of three mutually perpendicular directions (total of 36 times), so that the motion shall be applied for a total period of approximately 12 hours. interruptions are permitted provided the requirements for rate of change and test duration are met. thermal resistance thermal resistance (c/w) by case length # of sides heatsinked insulation 36.4 (mm) 45.9 (mm) 53.8 (mm) 66.5 (mm) one side bare can 6.60 5.20 4.44 3.60 polyester 7.78 6.13 5.24 4.24 both sides bare can 4.95 3.87 3.30 2.66 polyester 5.54 4.34 3.70 2.98 typical weight case aa - 19g, case ab - 22g, case ac - 26g, case ad - 34g terminals 20 aw copper wire with tin electroplate, 15 amps max case material li it a tailess teel leee ripple current capability the max ripple current capability is set by the target core temperature of 105 oc. the peak to peak ac must be less than vr/5 max. air cooled the ripple currents in the ratings tables are for 85 oc ambient temperatures. heatsink cooled temperature rise from the hottest internal spot, the core, to ambient air is t = i 2 (max esr)(cc ca), recommended max t of 20 oc where cc is the thermal resistance from core to case and ca from case to ambient. to calculate maximum ripple capability with the thas attached to a heatsink use the maximum core temperature and the values for cc. example as an illustration, suppose you operate an noninsulated thas112m060aa0c in 85 oc air and attach it to a commercial heatsink with a free-air thermal resistance of 2.7 oc/w. se a good thermal grease between the capacitor and the heatsink, and the total thermal resistance is 2.7 6.6 or 9.3 o c/w. the power which would heat the core to 105 c is (105 - 85)/9.3 or 2.15 w. for an esr of 117 m, 2 .15 w equates to a ripple current of 4.28 a. cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 type thas,thinpack, aluminum electrolytic capacitor, 105 oc
part numbering system thas 412 m 025 aa 0 c type capacitance tolerance rated voltage case code insulation mounting style thas 322 =3200 f 222 = 2200 f 162 = 1600 f m= 20% 025 = 25 vdc 075 = 75 vdc 150 = 150 vdc 200 = 200 vdc aa = 36.4 mm ab = 45.9 mm ac = 53.8 mm ad = 66.5 mm 0 = bare can 1 = polywrap c = two leads outline drawing cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 type thas,thinpack, aluminum electrolytic capacitor, 105 oc note: the polyester tape wrap may add up to 0.020 inches to the thickness and width of the capacitor. style c: no tabs l0.5 mm 50mm min 10mm 0.25 mm 25.4mm0.3 mm 2mm max 9.0mm 0.3mm 0.82mm dia 20 awg leads (typ) 30
cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 ratings type thas,thinpack, aluminum electrolytic capacitor, 105 oc voltage cap (f) catalog part number length (l) esr max 25 c () 120 hz 20 khz ripple (a) case @ 85c 120 hz 20 khz 10 vdc @ 105 c 12 vdc surge @ 25 c 8500 thas852m010aa0c 36.4 0.12 0.09 2.00 2.20 11000 thas113m010ab0c 45.9 0.08 0.07 2.00 2.20 14000 thas143m010ac0c 53.8 0.07 0.06 2.60 2.86 18000 THAS183M010AD0C 66.5 0.05 0.04 3.50 3.85 16 vdc @ 105 c 19.2 vdc surge @ 25 c 5900 thas592m016aa0c 36.4 0.12 0.09 2.00 2.20 8200 thas822m016ab0c 45.9 0.08 0.07 2.20 2.42 10000 thas103m016ac0c 53.8 0.07 0.06 2.60 2.86 13000 thas133m016ad0c 66.5 0.05 0.04 3.50 3.85 20 vdc @ 105 c 24 vdc surge @ 25 c 5000 thas502m020aa0c 36.4 0.12 0.09 2.00 2.20 7000 thas702m020ab0c 45.9 0.08 0.07 2.20 2.42 8200 thas822m020ac0c 53.8 0.07 0.06 2.60 2.86 10000 thas103m020ad0c 66.5 0.05 0.04 3.50 3.85 25 vdc @ 105 c 30 vdc surge @ 25 c 3500 thas352m025aa0c 36.4 0.12 0.09 2.00 2.20 4900 thas492m025ab0c 45.9 0.08 0.07 2.60 2.86 6000 thas602m025ac0c 53.8 0.07 0.06 2.50 2.75 7800 thas782m025ad0c 66.5 0.05 0.04 3.10 3.41 30 vdc @ 105 c 36 vdc surge @ 25 c 2900 thas292m030aa0c 36.4 0.12 0.09 2.00 2.20 4100 thas412m030ab0c 45.9 0.08 0.07 2.60 2.86 5000 thas502m030ac0c 53.8 0.07 0.06 3.00 3.30 6500 thas652m030ad0c 66.5 0.05 0.04 3.50 3.85 35 vdc @ 105 c 42 vdc surge @ 25 c 2500 thas252m035aa0c 36.4 0.12 0.09 2.00 2.20 3500 thas352m035ab0c 45.9 0.08 0.07 2.60 2.86 4300 thas432m035ac0c 53.8 0.07 0.06 3.00 3.30 5600 thas562m035ad0c 66.5 0.05 0.04 3.60 3.96 40 vdc @ 105 c 48 vdc surge @ 25 c 2100 thas212m040aa0c 36.4 0.12 0.09 1.70 2.04 3000 thas302m040ab0c 45.9 0.08 0.07 2.20 2.64 3700 thas372m040ac0c 53.8 0.07 0.06 2.50 3.00 4800 thas482m040ad0c 66.5 0.05 0.04 3.10 3.72 50 vdc @ 105 c 60 vdc surge @ 25 c 1400 thas142m050aa0c 36.4 0.12 0.09 1.70 2.04 2000 thas202m050ab0c 45.9 0.08 0.07 2.20 2.64 2500 thas252m050ac0c 53.8 0.07 0.06 2.50 3.00 3200 thas322m050ad0c 66.5 0.05 0.04 2.90 3.48 60 vdc @ 105 c 72 vdc surge @ 25 c 1100 thas112m060aa0c 36.4 0.12 0.09 1.70 2.04 1600 thas162m060ab0c 45.9 0.08 0.07 2.20 2.64 2000 thas202m060ac0c 53.8 0.07 0.06 2.50 3.00 2600 thas262m060ad0c 66.5 0.05 0.04 3.10 3.72 75 vdc @ 105 c 90 vdc surge @ 25 c 680 thas681m075aa0c 36.4 0.29 0.19 1.10 1.43 940 thas941m075ab0c 45.9 0.21 0.14 1.40 1.82 1100 thas112m075ac0c 53.8 0.17 0.11 1.60 2.08 1500 thas152m075ad0c 66.5 0.13 0.09 2.00 2.60 100 vdc @ 105 c 120 vdc surge @ 25 c 310 thas311m100aa0c 36.4 0.29 0.19 1.10 1.43 430 thas431m100ab0c 45.9 0.21 0.14 1.40 1.82 530 thas531m100ac0c 53.8 0.17 0.11 1.60 2.08 690 thas691m100ad0c 66.5 0.13 0.09 2.00 2.60
cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 type thas,thinpack, aluminum electrolytic capacitor, 105 oc typical performance curves voltage cap (f) catalog part number length (l) esr max 25 c () 120 hz 20 khz ripple (a) case @ 85 c 120 hz 20 khz 150 vdc @ 105 c 180 vdc surge @ 25 c 230 thas231m150aa0c 36.4 0.80 0.40 0.60 1.02 320 thas321m150ab0c 45.9 0.58 0.29 0.80 1.36 400 thas401m150ac0c 53.8 0.47 0.24 1.00 1.70 520 thas521m150ad0c 66.5 0.37 0.18 1.20 2.04 200 vdc @ 105 c 240 vdc surge @ 25 c 120 thas121m200aa0c 36.4 0.90 0.45 0.60 1.02 170 thas171m200ab0c 45.9 0.65 0.33 0.80 1.36 210 thas211m200ac0c 53.8 0.53 0.27 0.90 1.53 270 thas271m200ad0c 66.5 0.41 0.21 1.10 1.87 250 vdc @ 105 c 300 vdc surge @ 25 c 110 thas111m250aa0c 36.4 0.90 0.45 0.60 1.02 150 thas151m250ab0c 45.9 0.65 0.33 0.80 1.36 190 thas191m250ac0c 53.8 0.53 0.27 0.90 1.53 250 thas251m250ad0c 66.5 0.41 0.21 1.10 1.87 300 vdc @ 105 c 350 vdc surge @ 25 c 90 thas900m300aa0c 36.4 0.90 0.45 0.60 1.02 130 thas131m300ab0c 45.9 0.65 0.33 0.80 1.36 160 thas161m300ac0c 53.8 0.53 0.27 0.90 1.53 200 thas201m300ad0c 66.5 0.41 0.21 1.10 1.87 350 vdc @ 105 c 400 vdc surge @ 25 c 80 thas800m350aa0c 36.4 2.45 1.18 0.60 1.02 110 thas111m350ab0c 45.9 1.78 0.85 0.60 1.02 130 thas131m350ac0c 53.8 1.45 0.70 0.70 1.19 170 thas171m350ad0c 66.5 1.12 0.54 0.80 1.36 400 vdc @ 105 c 450 vdc surge @ 25 c 70 thas700m400aa0c 36.4 2.45 1.18 0.60 1.02 90 thas900m400ab0c 45.9 1.78 0.85 0.60 1.02 110 thas111m400ac0c 53.8 1.45 0.70 0.70 1.19 140 thas141m400ad0c 66.5 1.12 0.54 0.80 1.36 450 vdc @ 105 c 500 vdc surge @ 25 c 60 thas600m450aa0c 36.4 2.45 1.18 0.60 1.02 80 thas800m450ab0c 45.9 1.78 0.85 0.60 1.02 100 thas101m450ac0c 53.8 1.45 0.70 0.70 1.19 130 thas131m450ad0c 66.5 1.12 0.54 0.80 1.36 1 10 100 1000 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 expected operating life, kh rated ripple - current multiple type thas operating life in kilohours vs ripple current 45 c 55 c 65 c 75 c 85 c 95 c 105 c
typical performance curves cdm cornell dubilier ? 140 technology place ? liberty, sc 29657 ? phone: (864)843-2277 ? fax: (864)843-3800 type thas,thinpack, aluminum electrolytic capacitor, 105 oc thas502m020aa0c 0.01 0.1 1.0 10.0 1 10 100 1000 10000 100000 1000000 |z| ( ) freq (hz) |z| vs. frequency & temp 105 85 65 45 25 0 -20 -40 -55 0.01 0.1 1.0 10.0 1 10 100 1000 10000 100000 1000000 esr ( ) freq (hz) esr vs. frequency & temp 105 85 65 45 25 0 -20 -40 -55 0.0 1000.0 2000.0 3000.0 4000.0 5000.0 6000.0 1 10 100 1000 10000 100000 1000000 cap (f) freq (hz) cap vs. frequency & temp 105 85 65 45 25 0 -20 -40 -55
notice and disclaimer: all product drawings, descriptions, specifcations, statements, information and data (collectively, the information) in this datasheet or other publication are subject to change. the customer is responsible for checking, confrming and verifying the extent to which the information con - tained in this datasheet or other publication is applicable to an order at the time the order is placed. all information given herein is believed to be accurate and reliable, but it is presented without any guaran - tee, warranty, representation or responsibility of any kind, expressed or implied. statements of suitability for certain applications are based on the knowledge that the cornell dubilier company providing such statements (cornell dubilier) has of operating conditions that such cornell dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representa - tion regarding any such matter C and cornell dubilier specifcally and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specifc customer application, use, storage, transportation, or operating environment. the information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. any technical advice inferred from this information or otherwise provided by cornell dubilier with reference to the use of any cornell dubilier products is given gratis (unless otherwise specifed by cornell dubilier), and cornell dubilier assumes no obligation or liability for the advice given or results obtained. although cornell dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indi - cated in such warnings, cautions and notes, or that other safety measures may not be required.
|
